亚洲一区欧美在线,日韩欧美视频免费观看,色戒的三场床戏分别是在几段,欧美日韩国产在线人成

低雷諾數工況下鋸齒型翅片性能的參數化研究
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:


Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 圖/表
  • |
  • 訪問統計
  • |
  • 參考文獻
  • |
  • 相似文獻
  • |
  • 引證文獻
  • |
  • 資源附件
  • |
  • 文章評論
    摘要:

    基于田口方法,結合均勻設計法對低雷諾數工況下錯列鋸齒型翅片進行三維參數化數值研究。以單層翅片組件為測試對象,對6種試件的試驗表明,仿真結果與試驗數據的趨勢吻合良好,而存在差異的主要原因是試件加工工藝引起翅片表面存在毛刺。按照均勻設計法得到6因子5水平的11種仿真方案,引入田口方法的信噪比和貢獻率,研究各幾何參數對翅片性能的影響程度,依次為齒距、齒高、齒型角、錯齒距、齒開窗寬度和齒厚。根據各水平下各可控因子的信噪比分布得到翅片的優化模型,并通過仿真驗證了優化模型的有效性。

    Abstract:

    Based on Taguchi method and uniform design method, the three-dimensional numerical parametrical study of offset strip fins was conducted at low Reynolds number. Taken the single fin assembly as test section, the experimental data for 6 scheme fins were obtained, which have the same tendency with the corresponding simulated data. The difference between them is due to the existence of burrs on fin surface caused by manufacturing technology. According to uniform design, the 11 test schemes with 6 factors and 5 levels were yielded. And by adopting the signal to noise ratio and the contribution ratio originated from Taguchi method, the affecting degree of each geometrical parameter on fin performance was investigated. The sequence of effective factors is fin wavelength, fin height, fin angle, staggered fin wavelength, fin width and fin thickness. According to the signal to noise ratio distribution of each control factor at each level, the optimum model was obtained and confirmed validly by the simulation.

    參考文獻
    相似文獻
    引證文獻
引用本文

郭麗華,覃峰,陳江平,夏立峰,陳芝久.低雷諾數工況下鋸齒型翅片性能的參數化研究[J].農業機械學報,2007,38(7):168-171.[J]. Transactions of the Chinese Society for Agricultural Machinery,2007,38(7):168-171.

復制
分享
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期:
  • 出版日期: