亚洲一区欧美在线,日韩欧美视频免费观看,色戒的三场床戏分别是在几段,欧美日韩国产在线人成

基于ANSYS的生物質液壓成型模具錐角優化
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:


of Mold Cone Angle of Hydraulic Briquetting Press Based on ANSYS
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    液壓成型機模具錐角是影響成型的關鍵參數，為降低壓縮過程中的摩擦力、減少消耗的壓縮能、提高成型燃料的成型密度和成型品質，運用ANSYS參數化語言，對液壓成型機模具錐角進行優化分析。研究了模具錐角值與應力分布關系、模具不同錐角時摩擦力與位移關系，得出錐角與應力分布呈二次拋物線形式。研究結果表明：模具錐角最佳取值范圍為5.5°～6.0°。經試驗，錐角在此范圍內取值，出模后的成型燃料松弛密度增大，耐久性增加，成型密度和成型品質提高。

    Abstract:

    Mold cone angle is an important parameter. The simulation of the main molding stage of hydraulic briquetting machine was carried out with the finite element software ANSYS, in which the special ANSYS parametric design language was used to optimize analysis the mold cone angle of hydraulic briquetting press. The relationship between mold cone angle and equivalent stress was studied, along with the relationship between the friction stress and displacement in different mold cone angle values. The result indicated the best range of mold cone angle of 5.5°～6.0° is obtained, in which, the simulation results are approximately in accordance with the measured values. Furthermore, the briquette block has a good density, and quality, and is suitable for storage and transportation.

    參考文獻
    相似文獻
    引證文獻
引用本文

劉超,董玉平,吳云玉.基于ANSYS的生物質液壓成型模具錐角優化[J].農業機械學報,2009,40(12):125-129. of Mold Cone Angle of Hydraulic Briquetting Press Based on ANSYS[J]. Transactions of the Chinese Society for Agricultural Machinery,2009,40(12):125-129.

復制
分享
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期:
  • 出版日期: